D Latch with Oscilloscope Circuit Simulator

交互式模拟器需要 JavaScript

启用 JavaScript 即可加载实时电路。下方真值表描述了该电路的行为。

您将学到什么

Use an oscilloscope to visualize latch input and output over time.
Identify transparent and hold phases by clock level.
See Q follow D during transparent phases and freeze during hold phases.
Recognize the importance of waveform-based debugging in sequential logic.
Connect oscilloscope traces to setup/hold timing requirements.

工作原理

This circuit pairs a clocked D latch with a multi-channel oscilloscope so you can see the timing relationship between clock, D input, and Q output. Watching traces over time makes the difference between transparent and hold mode obvious — and reveals why latches are level-sensitive rather than edge-triggered.

The oscilloscope traces: - Clock: Square wave from the clock generator. - D input: User-toggled or signal-generated data. - Q output: Reflects D when clock is high; freezes at the last value when clock falls.

Key timing features visible: - During clock-high: Q follows D with small propagation delay. - At clock falling edge: Q captures D's current value and holds it. - During clock-low: D may change but Q stays frozen. - At clock rising edge: Q immediately starts following D again.

This is the defining latch behaviour: level-sensitive transparency. Compare to a flip-flop whose Q only changes on a single clock edge per cycle, regardless of D activity during the rest of the cycle.

Using an oscilloscope to study sequential timing is exactly how engineers debug real circuits. Scope traces reveal setup/hold violations, glitches, and clock-domain mismatches that static analysis can miss.

逐步尝试

在上方嵌入式电路中设置输入，然后阅读预期结果并验证。

1

CLK = running D = 0 → 1

预期: Q traces D during high clock; freezes during low clock

您将看到: Watch the scope: every time the clock rises, Q starts following D. Every time the clock falls, Q freezes at the current value.
2

CLK = running D = toggle rapidly

预期: Q toggles only during clock-high windows

您将看到: Toggle D faster than the clock — the scope shows Q tracking only inside clock-high windows. Outside, Q is flat.
3

CLK = running D = static 0

预期: Q = 0 across the whole trace

您将看到: Static D, the latch reflects it. Q is 0 the whole time, regardless of clock. Latch behaviour reduces to a wire when D doesn't change.
4

CLK = stopped low D = 1 → 0 → 1

预期: Q frozen at last captured value

您将看到: Stop the clock low. Toggle D — Q ignores everything. The latch is fully closed. Re-start the clock to resume capturing.

使用的组件

实际应用

Lab debugging of sequential circuits. Real oscilloscopes (or logic analyzers) are essential for diagnosing latch/flip-flop timing issues — too-narrow setup margin, runt clock pulses, etc.

Pre-silicon timing verification. SPICE and waveform-based simulators show exactly the kind of trace this circuit displays — used to verify timing closure before tape-out.

Educational tool. Students learning sequential logic benefit enormously from seeing waveforms, not just truth tables. Behaviour over time is the essence of sequential logic.

ATE pattern verification. Automated test equipment captures device output waveforms and compares them against expected patterns — same waveform-comparison principle.

Bus protocol decoding. Logic analyzers attach to multi-bit buses and display traces of each line over time, with protocol decoders mapping waveforms to bus transactions.

常见问题

What does the oscilloscope add to my understanding?

Time. Truth tables describe steady-state behaviour but hide the dynamic relationships between clock, input, and output. Scope traces show propagation delay, the exact moment of Q-update, and any glitches during transitions.

What's the propagation delay from D to Q?

In real CMOS, ~50–500 ps. In the simulator, propagation is instantaneous (or one simulation step). Real designs use SPICE-level simulation to predict these delays accurately.

How would I diagnose a setup-time violation?

Watch the scope for D changing too close to the clock falling edge. If D is still settling when the clock closes, the latch may capture an indeterminate value or enter metastability. Lab testing uses sweeps of clock-D timing to find the violation threshold.

Can I see Q glitch when D glitches during clock-high?

Yes — that's the transparency hazard. Glitches on D propagate directly to Q while clock is high. The scope makes this visible. Edge-triggered flip-flops don't have this hazard because they only sample on the clock edge.

Why is waveform analysis so central to digital design?

Real circuits have analog physics (rise/fall times, capacitive loads, crosstalk) that affect digital behaviour. Static truth-table analysis misses these. Lab scopes, simulators, and logic analyzers all rely on waveform views to bridge the abstraction.